A little care and cleaning goes a long way to maintain the beauty of your Trex deck. All building that is exterior require cleaning and a Trex deck is not any different.

A little care and cleaning goes a long way to maintain the beauty of your Trex deck. All building that is exterior require cleaning and a Trex deck is not any different.


Composite Deck Care & Cleaning Guide

For early-generation composite services and products (Trex Accents , Trex Origins , Trex Contours , Trex Profilesor Trex Brasilia ), we recommend a semi-annual cleaning with a composite deck cleaner. Should your deck is amongst the superior products from Trex (Trex Transcend , Trex Enhance or Trex ch se ), soap-and-water cleaning or a mild pressure washing will do the trick. Discover ways to clean and care for your composite decking by reading the information that is applicable to your decking product and acquire prepared to enjoy maximum outd r coping with minimal upkeep.

Dirt and Debris

The area that is affected be sprayed down with a hose to get rid of area debris. Utilize soapy that is warm and a soft bristle brush to remove dirt and debris from the embossing pattern.

Using a Force Washer (General Cleaning Problems)

A pressure washer with no higher than 3100 psi** that has a fan soap and attachment/adjustment dispenser enables you to eliminate dust or mud. Spray deck with detergent, then follow by carefully scrubbing each deck board with a soft bristle brush. Spray/rinse each individual deck board utilizing a fan tip no closer than 8-in (203 mm) through the decking surface. RINSE THOROUGHLY. If dirty water from cleansing is left to dry, a movie will remain in the surface that is decking.

Problems with Concrete, Cement, Mortar, or Stucco Dust

When working with cement, concrete, mortar, or stucco, protect the decking whenever you can in order to not get dust particles on the surface that is decking. These particles, once they have hot or wet, causes a response regarding the surface that is decking have become tough to remove. If particles access it the decking surface, Trex recommends using Sakreteв„ў Concrete Dissolver ( sakrete /products/concrete-dissolver). MAKE SURE YOU FOLLOW MAKER’S GUIDELINES.

Tough Water Staining

Hard water is water with a high quantities of mineral deposits like lime, silica and calcium. When the water dries, deposits are left out, leaving ugly spots on surfaces. This is not a defect of Trex services and products but problem because of the water itself. Generally speaking, these deposits could be washed with white vinegar on decking surfaces. Rinsing is required, therefore care should be taken up to not make use of water that is hard this function. If difficult water must be used, dry having a cloth or use a blower to surfaces that are dry. In some instances a deck brightener item could also be used to greatly help clean hard water stains.

Chalk Lines

Many colored chalks are permanent and might discolor the top. Only use Irwin Strait-LineDust-Off Marking Chalk (purple), available at Irwin .

Tannins Due to Debris

Eliminate all debris through the deck utilizing a hose or br m. After the deck area is dry, use a deck “brightener”* to your deck as directed by the manufacturer. Deck Brighteners contain oxalic acid, that will also remove tannins.

Ice and snowfall

A plastic shovel may be used to remove snowfall through the deck. Utilize calcium chloride or rock sodium to melt the ice and snow from the deck surface.

Oil, Grease, and F d

All f d spills should be eliminated right as possible. The top must be washed within a week to steadfastly keep up the stain warranty. To eliminate, spray off with a hose and make use of warm, soapy water and a soft bristle brush to remove spills from the embossing pattern.


If debris such as for instance dirt and pollen is permitted to remain on the deck surface, mold can feast upon the biofilm. Employing a hose and hot, soapy water by having www.datingmentor.org/furfling-review/ a soft bristle brush is recommended to get rid of the f dstuff supply and mold.

Keeping Transcend and ch se Railing

NEVER usage acetone or other solvents on Trex Transcend and ch se railing to keep up the g d thing about the outer lining. For color transfer dilemmas (from accessory of baluster spacer), utilize Mr. Clean , Magic Eraser Original or Magic Eraser Extra capacity to assist remove this.**** For tiny surface scratches, marks or scuffs, usage Dupli-Color Scratch Seal в„ў Clear Sealer Pen.

Trex and Static Electricity

While it is not typical, static electricity may appear on walking areas in dry climates or in areas where dry winds and dust-borne particles lay on the decking surfaces. Fixed electricity can establish on occupants walking across any decking that is composite, including Trex, then make a small fixed shock when they touch a grounded metal area such as for example railing, d r, etc.

This condition can be decreased greatly with the use of a product call ACL StaticideВ®. Two products tested had been General Purpose Staticideand high quality StaticideВ®. Both are effective in greatly reducing electricity that is static Trex decking areas. Apply full power, employing a mop on a dry decking surface, and allow to dry; no rinsing or diluting needed. Products are non-toxic, non-flammable, non-staining (will maybe not change the color of decking surface), entirely biodegradable, and safe to utilize. Item is water-based and could require a 2nd application after rainfall or other climate. Over a period of time, the consequence of static will dissipate obviously regarding the decking surface.

See website link to learn more about product aclstaticide /antistatic_coatings.html

Rubber Mats

Be careful when utilizing mats that are rubber-backedi.e. welcome mats, etc.) as these may include substances that can often discolor or lighten the decking surface.

Job Web Site Storage

Shop decking on a level that is flat and ALWAYS utilize proper aids (dunnage). USUALLY DO NOT shop entirely on the ground. When stacking decking packages, supports (dunnage) should begin approximately 8-in (203 mm) from each end and be spaced more or less 2-ft (0.61m) on center. In addition, supports (dunnage) should line up vertically/perpendicular to the decking product. Adjust support blocks (dunnage) consequently if bundles are l se. For Select decking, Enhance decking, and 1×12 and 1×8 products, the maximum stack height is 12 packages. For all other decking products maximum stack height is 14 packages (ESSENTIAL TO NOTE THAT PROPER DUNNAGE SPACING MUST BE IN POSITION FOR THESE HEIGHTS). Whenever stacking numerous bundles, ensure that dunnage lines up vertically down through each stack. ALWAYS cover decking products on location until willing to be set up.